3X Chemistry Satin Suffocator, Gallon

Description

3X:Chemistry Suffocator is a single component, high solids paint specially formulated to bond to blasted or rusted metal surfaces. The coating forms a rock hard finish that's flexible, non-porous and will not crack, chip, flake or peel. No hardeners or activators are needed. Suffocator is completely unaffected by salt, gasoline, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
Permanently stops rust and corrosion. Can be sprayed or brushed over rusted surfaces. Reusable after opening. Highest percentage of solids. Available in Satin.
3X Chemistry Satin Suffocator, Gallon
Sku # 30746818
Mfr. Part # 3X-ESB01-EA-GAL
Condition
New
Brand
3X Chemistry
Sold
Each
Details
Info
3X:Chemistry Suffocator is a single component, high solids paint specially formulated to bond to blasted or rusted metal surfaces. The coating forms a rock hard finish that's flexible, non-porous and will not crack, chip, flake or peel. No hardeners or activators are needed. Suffocator is completely unaffected by salt, gasoline, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
Permanently stops rust and corrosion
Can be sprayed or brushed over rusted surfaces
Reusable after opening
Highest percentage of solids
Available in Satin
Charts
(PDF)
Installation Tips
Instructions
Preparation:
Remove all contaminants from the surface including grease, oil, etc. DO NOT use a solvent based chlorinated degreaser or those that contain kerosene, as these will leave a film that may hinder bonding. If the surface contains rust, use a wire brush to remove loose particles. For bare or sandblasted metal, use 3X Metal Etch to prep the surface for painting. It is imperative that all surfaces be allowed to dry thoroughly. Suffocator will adhere best to rough surfaces rather than smooth, glossy surfaces.
Mixing & Handling:
DO NOT SHAKE. Stir Suffocator gently and thoroughly. When opening, keep groves of original can clean of paint, or the can will seal permanently upon closing. Scoop only enough material from original container for use in one application. Before sealing, gently pour in just enough Reducer to cover surface of the paint in original can. DO NOT mix this solvent into the Suffocator. Let it remain on top until you are ready to use the product again. This will help prevent air from contacting the paint which will cause premature spoilage. Seal Immediately.
IMPORTANT: NEVER RETURN ANY UNUSED PORTION OF MATERIAL TO ORIGINAL CONTAINER.
Refrigeration of unused portion will help extend shelf life.
Application
Brushing:
Apply unreduced in thin, even coats using a disposable nylon brush. Heavy coats will inhibit the curing process and may cause bubbling. Fully cured in 48 to 72 hours based on environmental conditions.
Spraying:
If needed, thin up to 10% with Reducer. Use a spray tip between .013 and .017" with a pressure of 6-7 psi for HVLP guns; or 30-35 psi for conventional guns. Spray two medium wet coats, allowing 3 to 6 hours between coats. The second coat should be applied when the first coat seems hand slick but with a slight drag or tack to the surface. Fully cured in 48 to 72 hours depending on environmental conditions.
Note:
DO NOT apply Suffocator if surface and air temperature is less than 50°F.
Clean-up:
Clean tools and spray equipment immediately after with Reducer or Lacquer Thinner.
Top Coating/Priming:
Once fully cured, Suffocator may be wet sanded with 600 grit until finish is dull. Suffocator can then be top coated with any high quality, automotive finish.
Specs
Sold in Quantity
Each
Capacity
1.00
MFG. Part #
3X-ESB01-EA-GAL
Garage Sale Type
Closeout
Reviews
Just an amazing product, will definitely buy again.
Rated
by I like to move it move it on October 01, 2020
Summary:
I used this product underbody, after careful preparation. It without a doubt does exactly as is stated. Used according to label, my results are great and I now have piece of mind that my truck is ready for anything, especially since I unfortunately live in the rust belt. Best underside coating available, bar none. My truck is Encapsulated, one & done!
Pros:
I have piece of mind now
Yes, I recommend this product.
Shipping
Combined Shipping:
Please take advantage of the “add to cart” button on each listing to get everything in your cart prior to completing checkout. This will ensure you receive a combined shipping rate on your entire order.
Freight Shipping:
Some products are too large for standard ground delivery and must be shipped via truck freight.
Please contact us via eBay Message for a freight shipping estimate.
When possible, please provide a business or commercial address for delivery to eliminate additional fees.
Please ensure the phone number provided is accurate to avoid delays.
Upon delivery, the recipient must inspect the shipment before the driver leaves as there may be concealed damage; please open the carton to inspect the contents. Any visual damage must be noted on the shipping document BEFORE signing for delivery. Any damage not noted before signing for delivery is the buyer’s responsibility. If damage is found, the shipment may be refused, but please contact us as soon as possible and arrangements will be made to have the product replaced and damaged parts returned.
Tech Support
We're here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help.
About
Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 70 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.
Return Policy
We want you to be satisfied with your purchase. If within 60 days after you receive your shipment and you are not satisfied, you may return the item for a refund. Refunds will be processed (1-2) days after the item is received by Speedway. All returned merchandise must be in original factory condition with no modifications or alterations. A restocking fee up to 15% may be applied if items are not in new condition.
Returned merchandise must include all packaging materials, warranty cards, manuals, and accessories. If the items being returned need to be repackaged, there will be a repacking charge. Repack the item in a sturdy box, include a copy of your invoice and complete the form on the back of the invoice. You must ship orders back PREPAID. WE DO NOT ACCEPT COD SHIPMENTS.
All fiberglass items returned will be subject to a 15% restocking charge. No returns on electrical parts, DVDs, and books unless they are defective. Absolutely no returns on special order or closeout merchandise.
Payment
Accepted Payment Methods - PayPal and major credit cards are accepted.
Terms - Immediate payment is required on all listings.
To view states in which sales tax will apply to your order, please visit the “shipping and payments” tab.
Guarantee
Speedway accepts full responsibility for the accuracy of our listings and product representation. If an egregious shipping or description error occurs, we are happy to assist with a replacement or refund.
Disclaimer
Due to our large inventory and the diversity of our product line, the stock photo used may not be an exact representation of the item you are bidding on. Please read all product information carefully before purchase to avoid any order issues.